Question 1

Which of the following types of pliers would be most suitable for intricate electrical work?

Accepted Answer

A)   Linesman pliers
B)   Adjustable pliers
C)   Channellock pliers
D)   Needlenose pliersE) B) and C)
F) A) and D)

Question 2

Technician A says to replace all original Grade 5 fasteners with Grade 8 when performing suspension repairs.Technician B says that a Grade 8 rated Huck fastener may be replaced with a Grade 8 nut and bolt.Who is right?

Accepted Answer

A)   Technician A only
B)   Technician B only
C)   Both A and B
D)   Neither A nor BE) A) and B)
F) A) and C)

Question 3

Which of the following is best described as an online service information system (SIS) ?

Accepted Answer

A)   AccessFreightliner
B)   Wikipedia
C)   Google
D)   How stuff works?E) B) and D)
F) B) and C)

Question 4

Which of the following is true of an impact socket when compared to a standard socket?

Accepted Answer

A)   made of softer steel
B)   has a 12 point grip
C)   fractures more easily
D)   made only in 1/2-inch driveE) C) and D)
F) A) and B)

Question 5

Which of the following matches the term hex socket?

Accepted Answer

A)   4-point socket
B)   6-point socket
C)   8-point socket
D)   12-point socketE) A) and B)
F) A) and C)

Question 6

How is an arbor press actuated?

Accepted Answer

A)   Manually
B)   Pneumatically
C)   Hydraulically
D)   ElectricallyE) A) and C)
F) C) and D)

Question 7

Which of the statements below about the use of hand tools is TRUE?

Accepted Answer

A)   Use your thumb to help guide the hacksaw blade until the cut is started
B)   A slightly damaged,slotted screwdriver tip can be dressed using a hand file
C)   Pull on an adjustable wrench so that the force bears against the movable jaw
D)   Use a box-end wrench when there is insufficient access above a boltE) None of the above
F) A) and B)

Question 8

Which of the following is true of an Allen wrench?

Accepted Answer

A)   double hex drive
B)   hex drive
C)   8-point drive
D)   4-point driveE) B) and C)
F) C) and D)

Question 9

What should be used to remove a press-fit bearing from a shaft to minimize damage to both the shaft and the gear?

Accepted Answer

A)   hammer and drift
B)   pneumatic hammer
C)   bearing puller
D)   bearing mandrelE) None of the above
F) All of the above

Question 10

Through how many thimble rotations must a metric micrometer be turned to make the spindle move exactly 1.25 mm?

Accepted Answer

A)   1.25
B)   1.50
C)   2.25
D)   2.50E) A) and D)
F) A) and C)

Question 11

What should be used to mark the start point before drilling a hole in steel?

Accepted Answer

A)   diamond point chisel
B)   pin punch
C)   center punch
D)   aligning punchE) B) and D)
F) None of the above

Question 12

A wrench with open-end jaws at one end and box-end jaws at the other,both of the same nominal dimension,is known as a

Accepted Answer

A)   Linesman wrench
B)   Combination wrench
C)   Spanner wrench
D)   Adjustable wrenchE) None of the above
F) A) and B)

Question 13

What is an advantage of pneumatic tools over electric in a truck service shop environment?

Accepted Answer

A)   lightweight
B)   safer
C)   more flexible speed and torque
D)   all of the aboveE) C) and D)
F) A) and B)

Question 14

Technician A says that a beam type torque wrench should be as accurate as a click type.Technician B says that dial gauge type torque wrenches are ideal for torquing main cap bolts.Who is correct?

Accepted Answer

A)   Technician A only
B)   Technician B only
C)   Both A and B
D)   Neither A nor BE) B) and C)
F) A) and B)

Question 15

What tool is required to cut internal threads in hole?

Accepted Answer

A)   thread file
B)   tap
C)   die
D)   taper punchE) A) and B)
F) B) and C)

Question 16

When an IFI nut has two dots spaced less than 60-degrees apart,which of the following should be true?

Accepted Answer

A)   Grade 2 fastener
B)   Grade 5 fastener
C)   Grade 6 fastener
D)   Grade 8 fastenerE) A) and B)
F) A) and C)

Question 17

What is an advantage of a Posi-Drive screw over a Phillips screw?

Accepted Answer

A)   sustains higher torque
B)   more tamper resistant
C)   reduces slippage
D)   all of the aboveE) A) and D)
F) B) and C)

Question 18

Which of these statements about a standard micrometer is TRUE?

Accepted Answer

A)   The thimble is divided into 50 equal divisions
B)   A complete turn of the thimble moves the spindle through 0.050 inches
C)   20 complete rotations of the thimble moves the spindle 0.500 inch
D)   It should be stored with the spindle locked firmly against the anvilE) All of the above
F) A) and C)

Question 19

When measuring backlash between gears,which of the following measuring tools should be used to provide an accurate reading?

Accepted Answer

A)   outside micrometer
B)   inside micrometer
C)   dial caliper
D)   dial indicator with a magnetic baseE) A) and D)
F) A) and C)

Exam 3: Tools and Fasteners

When measuring backlash between gears,which of the following measuring tools should be used to provide an accurate reading?

Correct Answer
verified

Which of the following matches the term hex socket?

Correct Answer
verified

Which of the statements below about the use of hand tools is TRUE?

Correct Answer
verified

Which of the following types of pliers would be most suitable for intricate electrical work?

Correct Answer
verified

Technician A says to replace all original Grade 5 fasteners with Grade 8 when performing suspension repairs.Technician B says that a Grade 8 rated Huck fastener may be replaced with a Grade 8 nut and bolt.Who is right?

Correct Answer
verified

A wrench with open-end jaws at one end and box-end jaws at the other,both of the same nominal dimension,is known as a

Correct Answer
verified

Which of the following is true of an Allen wrench?

Correct Answer
verified

Through how many thimble rotations must a metric micrometer be turned to make the spindle move exactly 1.25 mm?

Correct Answer
verified

When an IFI nut has two dots spaced less than 60-degrees apart,which of the following should be true?

Correct Answer
verified

How is an arbor press actuated?

Correct Answer
verified

What tool is required to cut internal threads in hole?

Correct Answer
verified

What should be used to mark the start point before drilling a hole in steel?

Correct Answer
verified

Technician A says that a beam type torque wrench should be as accurate as a click type.Technician B says that dial gauge type torque wrenches are ideal for torquing main cap bolts.Who is correct?

Correct Answer
verified

Which of the following is true of an impact socket when compared to a standard socket?

Correct Answer
verified

Which of these statements about a standard micrometer is TRUE?

Correct Answer
verified

What should be used to remove a press-fit bearing from a shaft to minimize damage to both the shaft and the gear?

Correct Answer
verified

What is an advantage of a Posi-Drive screw over a Phillips screw?

Correct Answer
verified

What is an advantage of pneumatic tools over electric in a truck service shop environment?

Correct Answer
verified

Which of the following is best described as an online service information system (SIS) ?

Correct Answer
verified

Exam 3: Tools and Fasteners

When measuring backlash between gears,which of the following measuring tools should be used to provide an accurate reading?

Correct AnswerverifiedShow Answer

Which of the following matches the term hex socket?

Correct AnswerverifiedShow Answer

Which of the statements below about the use of hand tools is TRUE?

Correct AnswerverifiedShow Answer

Which of the following types of pliers would be most suitable for intricate electrical work?

Correct AnswerverifiedShow Answer

Technician A says to replace all original Grade 5 fasteners with Grade 8 when performing suspension repairs.Technician B says that a Grade 8 rated Huck fastener may be replaced with a Grade 8 nut and bolt.Who is right?

Correct AnswerverifiedShow Answer

A wrench with open-end jaws at one end and box-end jaws at the other,both of the same nominal dimension,is known as a

Correct AnswerverifiedShow Answer

Which of the following is true of an Allen wrench?

Correct AnswerverifiedShow Answer

Through how many thimble rotations must a metric micrometer be turned to make the spindle move exactly 1.25 mm?

Correct AnswerverifiedShow Answer

When an IFI nut has two dots spaced less than 60-degrees apart,which of the following should be true?

Correct AnswerverifiedShow Answer

How is an arbor press actuated?

Correct AnswerverifiedShow Answer

What tool is required to cut internal threads in hole?

Correct AnswerverifiedShow Answer

What should be used to mark the start point before drilling a hole in steel?

Correct AnswerverifiedShow Answer

Technician A says that a beam type torque wrench should be as accurate as a click type.Technician B says that dial gauge type torque wrenches are ideal for torquing main cap bolts.Who is correct?

Correct AnswerverifiedShow Answer

Which of the following is true of an impact socket when compared to a standard socket?

Correct AnswerverifiedShow Answer

Which of these statements about a standard micrometer is TRUE?

Correct AnswerverifiedShow Answer

What should be used to remove a press-fit bearing from a shaft to minimize damage to both the shaft and the gear?

Correct AnswerverifiedShow Answer

What is an advantage of a Posi-Drive screw over a Phillips screw?

Correct AnswerverifiedShow Answer

What is an advantage of pneumatic tools over electric in a truck service shop environment?

Correct AnswerverifiedShow Answer

Which of the following is best described as an online service information system (SIS) ?

Correct AnswerverifiedShow Answer

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified