Question 1

​Too light of a feed roller pressure can _______________.

Accepted Answer

A)   ​prevent damage to the welding wire
B)   ​be used to prevent bird-nesting
C)   ​cause erratic wire feeding
D)   ​help to reduce the roller's wearE) A) and C)
F) B) and C)

Question 2

​Which of the following gases is the least dense?

Accepted Answer

A)   ​Oxygen
B)   ​Carbon dioxide
C)   ​Argon
D)   ​HeliumE) All of the above
F) None of the above

Question 3

​The wire feed speed on charts are generally given in ___________________.

Accepted Answer

A)   ​pounds for filler wire per minute
B)   ​amperage and voltage
C)   ​pounds per square inch of weld area
D)   ​inches per minuteE) C) and D)
F) A) and B)

Question 4

The ____ the density of a gas, the ____ will be the flow rate required for equal arc protection.

Accepted Answer

A)   lower, lower
B)   lower, higher
C)   higher, higher
D)   lower, slowerE) B) and C)
F) B) and D)

Question 5

The more cost efficient welders can be, the more ___________ they and their companies become.

Accepted Answer

The answer of The more cost efficient welders can be,...

Question 6

With the feed running, adjust the ____________________ so that the reel stops when the feed stops.

Accepted Answer

The answer of With the feed running, adjust the ____________________...

Question 7

​Short electrode stickout gives a _____ weld and a long stickout results in a ______ weld.

Accepted Answer

A)   ​slower, faster
B)   ​wider, deeper
C)   ​higher buildup, deeper penetrating
D)   ​hotter, coolerE) A) and B)
F) None of the above

Question 8

Shielding gases in the gas metal arc process are used primarily to protect the molten metal from oxidation and ____________________.

Accepted Answer

The answer of Shielding gases in the gas metal arc...

Question 9

High gas flow rates ____.

Accepted Answer

A)   provide better weld coverage
B)   waste shielding gases
C)   decrease the venturi effect
D)   decrease contaminationE) B) and D)
F) All of the above

Question 10

​The only difference between all GMA welding machines and some FCA welding machines is that all GMA welding machines must have a ______________.

Accepted Answer

A)   ​cooling water system
B)   ​shielding gas solenoid
C)   ​air cooling fan
D)   ​power contactor to start and stop the currentE) All of the above
F) A) and C)

Exam 11: Gas Metal Arc Welding

Shielding gases in the gas metal arc process are used primarily to protect the molten metal from oxidation and ____________________.

Correct Answer
verified

With the feed running, adjust the ____________________ so that the reel stops when the feed stops.

Correct Answer
verified

The only difference between all GMA welding machines and some FCA welding machines is that all GMA welding machines must have a ______________.

Correct Answer
verified

Too light of a feed roller pressure can _______________.

Correct Answer
verified

The wire feed speed on charts are generally given in ___________________.

Correct Answer
verified

The more cost efficient welders can be, the more ___________ they and their companies become.

Correct Answer
verified

The the density of a gas, the will be the flow rate required for equal arc protection.

Correct Answer
verified

Which of the following gases is the least dense?

Correct Answer
verified

High gas flow rates ____.

Correct Answer
verified

Short electrode stickout gives a _ weld and a long stickout results in a __ weld.

Correct Answer
verified

Exam 11: Gas Metal Arc Welding

Shielding gases in the gas metal arc process are used primarily to protect the molten metal from oxidation and ____________________.

Correct AnswerverifiedShow Answer

With the feed running, adjust the ____________________ so that the reel stops when the feed stops.

Correct AnswerverifiedShow Answer

​The only difference between all GMA welding machines and some FCA welding machines is that all GMA welding machines must have a ______________.

Correct AnswerverifiedShow Answer

​Too light of a feed roller pressure can _______________.

Correct AnswerverifiedShow Answer

​The wire feed speed on charts are generally given in ___________________.

Correct AnswerverifiedShow Answer

The more cost efficient welders can be, the more ___________ they and their companies become.

Correct AnswerverifiedShow Answer

The ____ the density of a gas, the ____ will be the flow rate required for equal arc protection.

Correct AnswerverifiedShow Answer

​Which of the following gases is the least dense?

Correct AnswerverifiedShow Answer

High gas flow rates ____.

Correct AnswerverifiedShow Answer

​Short electrode stickout gives a _____ weld and a long stickout results in a ______ weld.

Correct AnswerverifiedShow Answer

Correct Answer
verified

Correct Answer
verified

The only difference between all GMA welding machines and some FCA welding machines is that all GMA welding machines must have a ______________.

Correct Answer
verified

Too light of a feed roller pressure can _______________.

Correct Answer
verified

The wire feed speed on charts are generally given in ___________________.

Correct Answer
verified

Correct Answer
verified

The the density of a gas, the will be the flow rate required for equal arc protection.

Correct Answer
verified

Which of the following gases is the least dense?

Correct Answer
verified

Correct Answer
verified

Short electrode stickout gives a _ weld and a long stickout results in a __ weld.

Correct Answer
verified